Message: BROM ERROR S_DL_GET_DRAM_SETTINGS_FAIL (5054)
Meaning: The files you're trying to flash do not belong to or are not compatible with the phone you're trying to flash them to OR if you're getting the error while trying to format then it's likely you only loaded scatter file without the rest of the files in the firmware
Solution:
If you're trying to flash firmware, then ensure you're using the correct files. If you're sure they are, then try formatting before flashing again
If you're trying to format, then ensure you the scatter file you loaded onto SP flash tool has complete firmware file locations
Initialize scatter failed
Message: Error: Initialize scatter file failed. Please check the scatter file name you load is legal
Meaning: SP Flash tool doesn't accept the name format of your scatter file
Solution:
Ensure the scatter file wasn't renamed. If you're certain it wasn't, try a higher version of SP Flash tool
Error 8038
Message: Error 8038! Android download pmt is ready and layout has been changed
Meaning: SP Flash tool is having trouble writing to certain partitions due to some incompatibility
Solution:
Format the phone in SP flash tool (Do not format Bootloader) then try flashing the files again using Download
If Download doesnt work then do a firmware upgrade
If the MTK backup contains more than one scatter file, retry flashing with the other scatter file.
If that isn't feasible, try formatting first or use firmware upgrade
If that doesn't work, open the scatter file using Notepad++ and change __NODL_FAT to FAT by removing "__NODL_" .
Error 4032
Message: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using https://forum.hovatek.com/thread-440.html
Delete the sp flash tool folder then re-extract
Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
Consider using the latest version of Sp Flash tool
Format the phone before trying to flash the file(s) again
Error 5056
Message: BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069)
Meaning: The size of a file is larger than the available / possible partition size
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Try another stock ROM
Change the phone's emmc chip
Error 4001
Message: S_FT_DA_NO_RESPONSE or Da didn't send response data to FlashTool!
Meaning: SP flash tool is having difficulty communicating with the device
Solution:
Change the USB-port
Run SP flash tool as Admin
Ensure to install the correct drivers (see https://forum.hovatek.com/thread-440.html )
Try another PC and USB cord
Ensure the phone is switched off with a charged battery inside when connecting to the PC for flashing
Sp flash tool was successful but phone's calibration doesn't work
Message: Soft keys and touch screen don't work / respond
Solution:
Edit the scatter file using Notepad++ and remove NODL__ (or set is_download: false to is_download: true ) in front of the items you have in the backup folder but aren't listed when you load the scatter file in SP flash tool. This way, these items will become listed when next you load the scatter file (after saving of course) and therefore flashable
Error 4008
Message: BROM ERROR : S_FT_DOWNLOAD_FAIL (4008)
Meaning: SP Flash tool encountered an error while attempting to flash files
Solution:
Ensure the battery is in the phone and the phone is switched off before connecting for flashing
Try using a higher version of SP flash tool
Change the USB cord and port or PC
Use the format option then download in SP flash tool
Error 3149
Message: BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3149)
Meaning: SP Flash tool was unable to flash files to the phone
Solution:
Ensure to run the latest version of SP flash tool as Administrator
Format first then Download
Don't tick a box with an unspecified / empty file path
Ensure the phone is switched off (with a well charged battery in it ) before connecting to PC for flashing
Try a different PC
Try a different ROM
Try a different USB cord
Try formatting the phone first before flashing files to it
Error 3168
Message: BROM ERROR: S_CHIP_TYRE_NOT_MATCH(3168)
Meaning: Sp flash tool believes there's a mismatch between the information provided in the scatter file and the phone's info.
Solution:
Ensure you're using the ROM for the exact phone model
Try a higher version of SP flash tool
Ensure to install the correct drivers for the phone on the PC
Error 2004
Message: BROM ERROR : S_FT_DOWNLOAD_FAIL (2004)
Meaning: There was an interruption in the communication between SP flash tool and the device
Solution:
A Secure Boot Download Agent (DA) might be required
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
USB device not recognized
Message: USB device not recognized prompt at system tray after connecting the phone to PC
Meaning: The PC is having problems communicating with the phone (often due to interruption, hardware or driver problems)
Solution:
Follow the guide @ https://forum.hovatek.com/thread-808.html
Try a different USB cord, PC port or PC
Error 1013
Message: BROM ERROR:S_COM_PORT_OPEN Fail(1013)
Meaning: SP flash tool encountered an error while attempting to communicate with the phone via the target port
Solution:
Try using a different port on the PC
Try a different version of SP flash tool
Install VCOM drivers using https://forum.hovatek.com/thread-440.html
Ensure the phone is switched off with battery inside before connecting to the PC for flashing
Try using a different PC
Try changing the USB cord
Ensure the phone's USB port isn't damaged
Error 2020
Message: BROM ERROR : S_BROM_CHKSUM16_MEM_RESULT_DIFF (2020)
Meaning: SP flash tool encountered a problem moving the files to be flashed into the phone's internal SRAM
Solution:
Use the latest version of SP flash tool
In SP flash tool, navigate to Options > Option > Connection > Battery. Set it to "with battery".
Use the Format all + Download option
Hold both volume buttons before connecting to the PC for flashing and release once flashing begins
Error 5007
Message: BROM ERROR : S_FTHND_FILE_IS_NOT_LOADED_YET (5007)
Meaning: You're trying to flash an item with an unspecified path (no file selected for the ticked item/box)
Solution:
Ensure the scatter file is in the same directory as the other file(s) to be flashed
Untick any item whose file you do not have or whose path is not specified; yet, is ticked / selected for flashing
Error 4010
Message: BROM ERROR : S_FT_FORMAT_FAIL
Meaning: The blocks map in the scatter file doesn't match the phone's partition sizes
Solution:
Try using the latest version of Sp flash tool
Try using another firmware for the exact phone model
Error 3182
Message: BROM ERROR: S_STORAGE_NOT_MATCH (3182)
Meaning: The ROM your're trying to flash is not compatible with the target device
Solution:
Download the ROM for the exact phone model you're trying to flash
Ensure to install VCOM drivers on the PC
Don't tick any box (after loading the scatter file) without a file path / whose corresponding file has not been automatically or manually loaded.
Error 6012
Message: BROM ERROR: S_SECURITY_SF_CODE_COMMAND_FORBIDDEN (6012), MSP ERROR CODE: 0X00
Meaning: The Download-Agent being used is incompatible with the phone
Solution:
Set Download-Agent to MTK_AllInOne_DA.bin
Error 1042
Message: BROM ERROR: S_TIMEOUT (1042)
Meaning: The flashing process took too long so SP flash tool encountered a timeout
Solution:
Try flashing one file at a time
Use the latest version of SP flash tool
Try using a different PC and USB cord
Try Infinix Flash tool @ https://forum.hovatek.com/thread-9224.html
Error 2
Message: BROM ERROR: ?? (2)
Meaning: SP Flash tool was unable to communicate with the phone
Solution:
Try using a different PC (preferably Windows 7 or lower)
Install the correct VCOM drivers for your PC's OS and architecture (32 or 64 bit)
Try another USB cord
Error 2005
Message: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
Meaning: The device attempted to power on before SP flash tool could flash files to it
Solution:
Ensure the battery is well charged
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
Do not hold any button when connecting to PC
Error 4058
Message: BROM ERROR: S_FT_GET_MEMORY_FAIL (4058)
Meaning: SP flash tool was unable to locate the partition you're trying to flash to
Solution:
Untick any item (box) with a blank or empty Location
Ensure that the memory and other components are properly seated on the board
Error 3178
Message: BROM_ERROR_S_STORAGE_NOT_MATCH (3178)
Meaning: The firmware you are trying to flash isnt compatible with your phone
Solution:
Try flashing another firmware for your exact phone model / variant
Error 8406
Message: SP FLASH TOOL ERROR (8406)
Meaning: There is some compatibility problem interrupting the flashing process
Solution:
Try flashing another firmware for your exact model
Update VCOM drivers for the device under Device manager
Error 1012
Message: BROM ERROR: S_NOT_ENOUGH_MEMORY (1012)
Meaning: The version of SP flash tool you're using doesn't support the size(s) of the file(s) in the firmware / stock ROM.
Solution:
Use the latest version of SP flash tool
Error 3140
Message: BROM ERROR : S_DA_UPDATE_BOOLOADER_EXIST_MAGIC_NOT_MATCHED
Meaning: SP flash tool encountered an error flashing a selected file to a non-specified partition
Solution:
Try using the latest version of SP flash tool
Use the format option then download in SP flash tool
Error 8417
Message: BROM ERROR: Initialize scatter file failed. Please check the scatter file name you load is legal
Meaning: The format of the scatter file is invalid
Solution:
Open the scatter file in Notepad++, the first line must begining with:
############################################################################################################## General Setting #
If there is anything else above this then delete it and save the scatter file
Error 6047
Message: BROM ERROR: S_SECURITY_SECURE_USB_DL_IMAGE_HASH_FAIL
Meaning: Hash (integrity) check of the images being flashed failed.
Solution:
Use SP Flash Tool V5.1516.00
Ensure to select the right Download-Agent
Navigate to Options > Option > Download and untick DA DLL All.....
Error 6010
Message: BROM ERROR: SP FLASHTOOL ERROR 6010 CODE DOWNLOAD FORBIDDEN
Meaning: The phone has a protected bootloader
Solution:
Untick Preloader and flash the rest
Error: 0xFDA
Message: BROM ERROR: S_FT_GET_MEMORY_FAIL (0xFDA)
Meaning: SP Flash tool encountered an error reading the phone's storage
Solution:
Try using a different USB Port, Cord and PC
Error 0x13BE
Message: S_DL_GET_DRAM_SETTING_FAIL (0x13BE)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Error:?? (0x3)
Message: BROM ERROR:?? (0x3)
Meaning: SP Flash tool encountered an error maintaining a connection to the device during flashing
Solution
Reinstall the VCOM drivers
Try a different PC and USB cord
The scatter file needs to be modified using https://forum.hovatek.com/thread-12719.html
PRO_INFO: Failed to get PMT info
Message: PRO_INFO: Failed to get PMT info
Meaning: SP flash tool is having problems reading the phone
Solution
Try using a different PC and USB cord
Ensure the phone is switched off (with a charged battery inside) when you connect
Error 0x7D4
Message: BROM ERROR: S_BROM_DOWNLOAD_DA_FAIL
Meaning: SP Flash tool encountered an error writing to the phone
Solution
Try changing the Download Agent (Secure Boot DA)
Try using a different USB cord, PC port and PC
Use the latest version of SP flash tool
Ensure the battery is well charged and the phone's USB port isn't faulty
Ensure the file name matches what's in the scatter file
Error 6124
Message: BROM ERROR: S_SECURITY_INVALID_PROJECT (6124), MSO ERROR CODE: 0X00
Meaning: Wrong flash settings or firmware
Solution:
Ensure you set the correct Download-Agent in SP flash tool and are using a firmware for your exact model
Go to Options > Option > Connection > USB Speed > Full Speed
Go to Options > Option > Download > Untick DA DL All with Checksum
Error 0x8
Message: BROM ERROR: ?? (0x8)
Meaning: The size of a file is larger than the available / possible partition size
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Try another stock ROM
Change the phone's emmc chip
Try using a different PC
Error OXFC0
Message: BROM ERROR S_FT_ENABLE_DRAM_FAIL (OXFC0)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using
Delete the sp flash tool folder then re-extract
Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
Consider using the latest version of Sp Flash tool
Format the phone before trying to flash the file(s) again
Error 0X411
Message: BROM ERROR: S_CHKSUM_ERROR (0X411)
Meaning: There was a checksum error when flashing the firmware
Solution
Delete any file with checksum in its name from the firmware folder
Go to Options > Option > Download > Untick Da DL all with checksum
Error 0xFA1
Message: BROM ERROR : S_FT_DA_NO_RESPONSE (0xFA1)
Meaning: SP Flash tool encountered an error communicating with the device
Solution
Try using a different port, PC and USB cord
Ensure the phone is switched off with a charged battery inside
Do not hold any button when connecting for flashing
Ensure to install VCOM drivers @ https://forum.hovatek.com/thread-440.html
Error 4017
Message: BROM ERROR: S_FT_NAND_READLEN_NOT_ALIGNMENT (4017)
Meaning: You're trying to flash a file that has not been processed for flashing in SP flash tool
Solution:
If you're using an MTK Droid tools backup then ensure to carry out Phase II @ https://forum.hovatek.com/thread-468.html
TOOL DL image Fail !
Message: TOOL DL image Fail !
Meaning: The firmware was flashed with Da DL all with Checksum disabled
Solution:
In SP flash tool, navigate to Options > Option > Download > Tick Da Dl all with checksum > Reflash the firmware
Please select one ROM at least before execution
Message: Please select one ROM at least before execution
Meaning: SP flash tool fails to recognize that there is an item ticked
Solution:
Select the scatter file again and untick all items you do not wish to flash one after the other. Don't use the checkbox beside "Name" in SP flash tool
Error 0xFC0
Message: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (0xFC0)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using https://forum.hovatek.com/thread-440.html
Delete the sp flash tool folder then re-extract
Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
Consider using the latest version of Sp Flash tool
Format the phone before trying to flash the file(s) again
Error: 0xC0050003
Message: BROM ERROR: STATUS_DOWNLOAD_EXCEPTION (0xC0050003)
Meaning: There was an interruption during writing to one or more partitions
Solution:
Repeat flashing with the latest version of SP Flash Tool
Try using a different Port, USB cord and PC
Try flashing one partition at a time
Error: 0xc002002A
Message: BROM ERROR: STATUS_SEC_IMG_TYPE_MISMATCH (0xc002002A)
Meaning: The firmware you're trying to flash is either not compatible with your device, you have selected the wrong flashing settings or verified boot is enabled
Solution:
Try unlocking the bootloader before flashing
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using https://forum.hovatek.com/thread-440.html
Delete the sp flash tool folder then re-extract
Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
Consider using the latest version of Sp Flash tool
Format the phone before trying to flash the file(s) again
Error 0XFA8
Message: BROM ERROR: S_FT_DOWNLOAD_FAIL (0XFA8)
Meaning: SP Flash tool encountered an error while attempting to flash files
Solution:
Ensure the battery is in the phone and the phone is switched off before connecting for flashing
Try using the latest version of SP flash tool
Change the USB cord and port or PC
Use the format option then download in SP flash tool
Try changing the Download Agent setting in SP Flash tool
Error 0x7D5
Message: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (0x7D5)
Meaning: The device attempted to power on before SP flash tool could flash files to it
Solution:
Ensure the battery is well charged
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
Do not hold any button when connecting to PC
Boundary Check Failed
Message: Boundary Check Failed: rom_end_addr >= next rom begin_addr.
Meaning: The firmware has a partition that wasn't included while backing up the firmware. SP flash tool encounters an error in the end address of the preloader partition and the begin address of PGPT partition (i.e the partition which wasn't included in the backup)
Solution:
Close the error message, then manually select the location of all files in the scatter file from the bottom to the top. Meaning that preloader would be the last thing you'll select
If that doesn't work, open and modify the scatter file using Notepad++ then change "boundary_check: True" to "boundary_check: False"
If after modifying the scatter file and you still encounter the same or a different error, then flash the firmware using miracle box @ https://forum.hovatek.com/thread-14106.html
Error 3179
Message: BROM ERROR : S_CHIP_TYPE_NOT_MATCH (3179)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using https://forum.hovatek.com/thread-440.html
Delete the sp flash tool folder then re-extract
Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
Consider using the latest version of Sp Flash tool
Format the phone before trying to flash the file(s) again
Error 5073
Message: BROM ERROR : S_DL_READ_PT_FAIL (5073)
Meaning: SP flash tool encountered an error while trying to format the device
Solution:
Use "download only" under the download tab to flash the firmware then you can format if need be.
SP Flash Tool force-closes when scatter file is loaded
Message: SP Flash tool automatically closes after selecting a scatter file
Meaning: SP Flash Tool doesn't support the scatter file due to its blocks or configuration
Solution:
Open the scatter file using Notepad++ > Locate the last partition on the list (flashinfo) > change is_download from true to false > Save the scatter file and reload
Storage type mismatch!
Message: scatter storage type is HW_STORAGE_EMMC
target storage type is HW_STORAGE_NAND
Meaning: There's a mismatch between the phone's storage type and that which the scatter file expects
Solution:
Try using a different firmware or a Chinese box @ https://forum.hovatek.com/forum-97.html
Try a different version of SP Flash tool and run as Administrator
Error 8045
Message: No Valid Partition Management Table (PMT) for storage
Meaning: SP Flash tool encountered a problem identifying the device's partitions ahead of file writes
Solution:
Try Flashing the firmware using Download only
Error 1041
Message: BROM ERROR: S_CHKSUM_ERROR (1041)
Meaning: There was a checksum error when flashing the firmware
Solution
Delete any file with checksum in its name from the firmware folder
Go to Options > Option > Download > Untick Da DL all with checksum
0x00
Message: BROM ERROR: S_SECURITY_AC_REGION_NOT_FOUND_IN_SECROIMG (6128), MSP ERROR CODE: 0X00
Meaning: The ROM contains a Checksum file but DL All With CheckSum was unticked
Solution:
Ensure to tick DL All With CheckSum under Options > Option > Download
BROM ERROR : S_SECURITY_SECRO_HASH_INCORRECT (6126) , MSP ERROE CODE : 0x00
Message: BROM ERROR : S_SECURITY_SECRO_HASH_INCORRECT (6126) , MSP ERROE CODE : 0x00
Meaning: The ROM contains a Checksum file but DL All With CheckSum was unticked
Solution:
Ensure to tick DL All With CheckSum under Options > Option > Download
Error 0xC0050005
Message: ERROR STATUS_EXT_RAM_EXCEPTION (0xC0050005)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash
Error (3)
Message: BROM ERROR: ?? (3)
Meaning: There's a problem with the format of the scatter file or file(s) being flashed. An example is trying to flash .bin files using SP Flash Tool
Solution:
Check the scatter file and files you're about flashing to be sure they're not meant to be flashed using a different tool
Error 6104
Message: BROM ERROR: S_SECURITY_SECURE_USB_DL_DA_RETURN_INVALID_TYPE (6104), MSP ERROR CODE : 0X00
Meaning: Wrong flash settings or firmware
Solution:
Ensure you set the correct Download-Agent in SP flash tool and are using a firmware for your exact model
Go to Options > Option > Connection > USB Speed > Full Speed
Go to Options > Option > Download > Untick DA DL All with Checksum
Error 3183
Message: BROM ERROR: S_CHIP_TYRE_NOT_MATCH(3183)
Meaning: Sp flash tool believes there's a mismatch between the information provided in the scatter file and the phone's info.
Solution:
Ensure you're using the ROM for the exact phone model
Try a higher version of SP flash tool
Ensure to install the correct drivers for the phone on the Pc
Error 0xC0060001
Message: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (0xC0060001)
Meaning: The device attempted to power on before SP flash tool could flash files to it
Solution:
The device might require a custom Download Agent (DA) to be flashed
Ensure the battery is well charged
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
Do not hold any button when connecting to PC
PMT changed for the ROM
Message: PMT changed for the ROM; it must be downloaded
Meaning: The partition table about to be written (from the scatter file) is different from the phone's current partition table layout
Solution:
Ensure that the scatter file / files you're trying to flash are actually for your exact model
If you're trying to flash just a few files and not the firmware then you need to get the firmware to complement and then flash using download only
If you're trying to flash the full firmware then try using the Firmware Upgrade option or Format first before download only
Error 6004
Message: ERROR: S_SECURITY_SLA_FAIL (6004), MSP ERROE CODE: 0X00
Meaning: The download agent isn't compatible with the device
Solution:
Try choosing a different Download Agent, version or tool
Ensure you're using the right Authentication file
Storage type mismatch!
Message:
scatter storage type is HW_STORAGE_EMMC
target storage type is HW_STORAGE_NONE
Meaning: There's a mismatch between the phone's storage type and that which the scatter file expects
Solution:
Try using SP Flash tool Version 3.x
Error 6045
Message: S_SECURITY_SECURE_USB_DL_IMAGE_SIGN_HEADER_NOT_FOUND (6045) , MSP ERROE CODE : 0x00
Meaning: The image files you are trying to flash doesn't contain the -sign header.
Solution:
Use SP Flash Tool V5.1532.00 @ https://forum.hovatek.com/thread-13970.html
Load the Auth file for the device in the flash tool
Ty flashing a factory (signed) firmware
Flash the unsigned image using the 'Write Memory' tab in SP flash tool. To activate write memory tab, press 'Ctrl + Alt + V' to enabled advanced mode then click Window > Write Memory
Error 2035
Message: BROM ERROR: S_BROM_CMD_JUMP_DA_FAIL (2035)
Meaning: SP Flash tool encountered an error connecting to the device.
Solution
Ensure the battery is inserted and you're not holding any button when connecting to PC for flashing
Uninstall all Mediatek drivers then re-install VCOM drivers
Disable any modem manager or software which might be blocking ports on the PC
For Linux / Ubuntu users, make sure you installed libusb-dev then blacklist Ubuntu’s modem manager (because it controls port /dev/ttyACM0, which is disabling SP Flash Tool from running properly).
Error 0x412
Message: BROM ERROR: S_TIMEOUT (0X412)
Meaning SP Flash tool encountered a timeout when trying to flash (i.e flashing took too long to start or complete)
Solution
Ensure that files are actually loaded (with valid location) in SP flash tool (i.e location should not be empty)
Try flashing one file at a time
Use a higher version of SP Flash tool
Untick the large files or find smaller alternatives
Error 6029
Message: S_SECURITY_SEND_AUTH_FAIL (6029) , MSP ERROE CODE : 0x00
Meaning SP Flash tool can't authenticate the files you are trying to flash
Solution
Try another ROM / firmware from a different source
Error 0x93AF
Message: ROM[logo] checksum mismatch checksum_config[0x93af],checksum_val[0x94ae]
Meaning SP Flash tool encountered a checksum error
Solution
Open the checksum file using notepad++, search for 0x93af and replace with 0x94ae
Delete any checksum file in the rom
Error 5011
Message: S_DL_SCAT_INCORRECT_FORMAT (5011)
Meaning The scatter file has incorrect format. The scatter file has been badly created / modified
Solution
Download a different scatter file (one that doesn't pop the same incorrect scatter file error in SPft), open the two scatter files using Notepad++ and you will notice that the incorrect scatter file has its items slightly shifted to the left. Edit the incorrect scatter file to the same format arrangement as in the working scatter file.
After modifying the scatter file using the method above, ensure to use a recent version of SP flash tool e.g SP flash tool v5.1728
Download another ROM / firmware from a different source
Error 0xC52
Message: ERROR: S_DA_SDMMC_WRITE_FAILED (0XC52)
Meaning: SP Flash tool was unable to flash files to the phone
Solution:
Ensure to run the latest version of SP flash tool as Administrator
Format first then Download
Don't tick a box with an unspecified / empty file path
Ensure the phone is switched off (with a well charged battery in it ) before connecting to PC for flashing
Try a different PC
Try a different ROM
Try a different USB cord
Try formatting the phone first before flashing files to it
Error 0xC0050005
Message: BROM ERROR: STATUS_EXT_RAM_EXCEPTION (0xC0050005)
Meaning: There was an overlap error while trying to flash the firmware
Solution:
Ensure the firmware you're trying to flash is for your phone's variant
Error 0XFAA
Message: BROM ERROR: S_FT_FORMAT_FAIL (0XFAA)
Meaning: The source (firmware) doesn't properly match the target (phone)
Solution:
Try using a different firmware for your phone model
Ensure you're using the right tool to flash the firmware
Error 5072
Message: ERROR: S_DL_WRITE_PT_FAIL (5072)
Meaning: SP flash tool is having problems writing to one or more partitions
Solution
Try using a different PC and USB cord
Ensure the phone is switched off (with a charged battery inside) when you connect
Do not hold any button when connecting to PC for flashing
Error 0xC0070004
Message: ERROR: STATUS_DA_HASH_MISMATCH (0xC0070004)
Meaning: Hash (integrity) check of the images being flashed failed.
Solution:
Use SP Flash Tool V5.1516.00
Ensure to select the right Download-Agent
Navigate to Options > Option > Download and untick DA DLL All.....
Error 6046
Message: BROM ERROR: S_SECURITY_USB_DL_IMAGE_SIGNATURE_VERIFY_FAIL (6064), MSP ERROR CODE: 0X0
Meaning: Signature verification for the firmware failed
Solution:
Set Download-Agent to MTK_AllInOne_DA.bin
Navigate to Options > Option > Download and untick DA DLL All.....
Delete any checksum file in the firmware folder
Error 0XC0060003
Message: ERROR: STATUS_BROM_CMD_SEND_DA_FAIL (0XC0060003)
Meaning: SP flash tool is unable to read or write to the device using the preset Download Agent
Solution:
The device might require a custom Download Agent (DA) to be flashed
Ensure the battery is well charged
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
Do not hold any button when connecting to PC
Error 0x94010000
Message: CHIP TYPE NOT match ! target refuse value: 0x94010000
Meaning: The device likely has a locked / encrypted preloader
Solution:
Untick preloader when flashing in Sp flash tool
Error 0xC0020029
Message: BROM ERROR: STATUS_SEC_IMGHDR_TYPE_MISMATCH (0xC0020029)
Meaning: You are trying to flash modified files to a device that only accepts signed or verified images
Solution:
Download and flash the official firmware (usually have -verified or -signed prefixes)
Error 5000
Message: BROM ERROR : S_AUTH_HANDLE_IS_NOT_READY (5000)
Meaning: The device has a secure boot / bootloader
Solution:
You'll need an Auth (*.auth) or custom Download Agent (DA) file for the device to proceed with SP flash tool
Error 0xC002002C
Message: ERROR : STATUS_SEC_IMG_HASH_VFY_FAIL (0xC002002C)
Meaning: The device has a verified boot
Solution:
You'll need to download and flash the official firmware (usually have -verified or -sign in their file name)
Error 0xC0030012
Message: ERROR: STATUS_SEC_AUTH_FILE_NEEDED (0xC0030012)
Meaning: The device has a secure boot
Solution:
You'll need to use a custom Download Agent (DA) for the model (check https://forum.hovatek.com/forum-112.html )
Error 0xC0060005
Message: ERROR: STATUS_BROM_CMD_FAIL (0xC0060005)
Meaning: The device attempted to power on before SP flash tool could flash files to it
Solution:
You'll need to use a custom Download Agent (DA) for the model
Error 8
Message: ERROR: ?? (8)
Meaning: The size of a file is larger than the available / possible partition size
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Try another stock ROM
Change the phone's emmc chip
Try using a different PC
Error 5002
Message: ERROR: S_INVALID_DA_FILE (5002)
Meaning: SP flash tool does not recognize the DA file. Most likely the DA file is locked / encrypted for use on a specific tool
Solution:
You'll either need to search for a DA file compatible with SP flash tool or use the specified tool for the DA file you downloaded [specified tool are usually hardware box / dongles e.g CM2mtk, volcano tool, e.t.c]
Error 0xC0030001
Message: Error: STATUS_SCATTER_FILE_INVALID (0xC0030001)
Meaning: SP flash tool does not recognize the scatter file or the location of the scatter file.
Solution:
Rename the folder location of the scatter file including the parent folders too, remove all special characters / non English characters from the folder name
If that doesn't work then create a new folder in your desktop then copy and paste ONLY the firmware files into the new folder then retry flashing the contents on the new folder
Partition[nvram] should NOT set "is_download" to true in scatter file
Message: Partition[nvram] should NOT set "is_download" to true in scatter file
Meaning: The scatter file loaded has nvram set to download but doesn't specify a file name for nvram. This error is common in later versions of SP flash tool
Solution:
Modify the scatter file using notepad++ and add a file name for nvram partition. e.g "file_name: nvram.bin" then save and ensure there's an nvram.bin file in the same folder as the scatter file. If that doesn't work then
Modify the scatter file using notepad++ and set "is_download: false" for nvram partition
Error 0xC0050001
Message: ERROR: STATUS_DEVICE_CTRL_EXCEPTION (0XC0050001)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Error 0xC002001B
Message: ERROR: STATUS_SEC_PUBK_AUTH_MISMATCH_N (0xC002001B)
Meaning: The device has a verified boot
Solution:
You'll need to download and flash the official firmware (usually have -verified or -sign in their file name)
Error 5014
Message: ERROR: S_DL_SCAT_ADDR_IS_NOT_ASCENDING_ORDER (5014)
Meaning: The scatter file was badly created or modified, depending on how you obtained the scatter file
Solution:
Input the correct values for all 'physical_start_addr' in the scatter file. The correct value for 'physical_start_addr' is the same as the value on 'linear_start_addr'
Error 0x7F3
Message: BROM ERROR: S_BROM_CMD_JUMP_DA_FAIL
Meaning: SP Flash tool encountered an error connecting to the device.
Solution
Ensure the battery is inserted and you're not holding any button when connecting to PC for flashing
Uninstall all Mediatek drivers then re-install VCOM drivers
Disable any modem manager or software which might be blocking ports on the PC
For Linux / Ubuntu users, make sure you installed libusb-dev then blacklist Ubuntu’s modem manager (because it controls port /dev/ttyACM0, which is disabling SP Flash Tool from running properly).
Error 3154
Message: BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3154)
Meaning: SP Flash tool was unable to flash files to the phone
Solution:
Ensure to run the latest version of SP flash tool as Administrator
Format first then Download
Don't tick a box with an unspecified / empty file path
Ensure the phone is switched off (with a well charged battery in it ) before connecting to PC for flashing
Try a different PC
Try a different ROM
Try a different USB cord
Try formatting the phone first before flashing files to it
Error 0xC0010005
Message: BROM ERROR: STATUS_PROTOCOL_ERR (0xC0010005)
Meaning: Sp flash tool is having problems communicating with the device
Solution: Ensure the phone is properly switched off (with battery connected) before connecting to PC for flashing.
Error 0xC0010007
Message: BROM ERROR: INSUFFICIENT_BUFFER (0xC0010007)
Meaning: SP flash tool seems to be blocked from flashing files to the phone
Solution:
If you can boot to fastboot mode, then unlock the bootloader then retry flashing
Untick OEM then retry flashing
Error 0xC0050007
Message: ERROR: STATUS_READ_DATA_EXCEPTION (0xC0050007)
Meaning: SP flash tool is unable to readback from the connected phone (esp where the readback length is too large)
Solution:
Download and install updated MTK drivers on your PC at [ Login / Register to download free]
If you're performing a readback, try skipping cache and userdata; see https://forum.hovatek.com/thread-22701.html
Error 0x13CD
Message: BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069)
Meaning: The size of a file is larger than the available / possible partition size
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Try another stock ROM
Change the phone's emmc chip
LIB DA not match
Message: LIB DA not match, please re-select DA or ask for help
Meaning: SP flash tool is having trouble using the selected DA file
Solution:
Untick 'Check LIB DA match' within SP flash tool general settings (Options > option)
Try another version of SP flash tool @ https://forum.hovatek.com/thread-13970.html ; you could try v5.1828 (it doesn't have this settings)
Error -1073283068
Message: BROM ERROR: STATUS_DA_HASH_MISMATCH (-1073283068), MSP ERROE CODE: 0X00
Meaning: The DA file being used isn't compatible
Solution: Try using a DA + Auth + Factory rom
Error 0XC50
Message: S_DA_SDMMC_CONFIG_FAILED (0XC50)
Meaning: The device likely has a protected preloader or bootloader
Solution: Untick preloader when flashing in Sp flash tool
Error 3152
Message: S_DA_SDMMC_CONFIG_FAILED (3152)
Meaning: The device likely has a protected preloader or bootloader
Solution: Untick preloader when flashing in Sp flash tool
0 comments:
Post a Comment